Is it possible for you to use an included return shipping label when receiving our materials?
Posted By: Jesus Mendoza on Aug 04, 2015 11:38PM Category: Ordering
Yes it is but it depends on how you provide the label to us.
Easiest would be a pdf attachment and requesting this method of shipping at checkout in Front Panel Designer. You can attached files to your order. Our shipping carriers are UPS and FedEx.
What we can't do is accessing your system (supplier portal etc) and pull shipping label from there.
Posted By: Diane Haensel on Aug 06, 2015 08:31PMReply
Hi, I'm trying to duplicate the switch panel that is shown on the RH side of the attached picture. Is it possible you could do something like that?
Attached File: Harrison_Lathe_Switch_Panel2.jpg
Posted By: Howard Clerf on Jul 11, 2015 02:22AM Category: Front Panel Designer
The panel itself is very easy since it has only a few mounting holes and cutouts for the controls. It is a bit more work to reproduce the image with all the machine settings and import it as vector graphic (plt format) into Front Panel Designer.
You can prepare the vector file with any graphic software.
Let me know if you need any help with this.
Posted By: Diane Haensel on Jul 13, 2015 11:25PMReply
For the Housing Profile 2, from the example , I can see the screw hole 'K' being specified on the Cover Panel pair 'B'.
But I did not see the corresponding holes for 'K' on the Housing Profile 2 in the example.
Are these hole required to be specified on the Housing probile 2 ? If so, how.
Posted By: Alan Tam on Jun 09, 2015 04:48PM Category: Front Panel Designer
You don't need to specify the holes on Housing Profile 2. This is where you want to use our square nuts (GGSO9903). They slide right into Housing Profile 2. You can move them to the desired position and line them up with the cover panel.
Posted By: Diane Haensel on Jun 09, 2015 07:07PMReply
Thanks for the reply.
I am planning for an enclosure with housing profile 2 on both side with a tall cover panel B, i.e. the 'FB' length is large with an narrow 'A' length.
I plan to install the housing bracket between cover panel B and the side panel.
I do not find such equation from the Housing Bracket section in the manual.
Have I missed anything from the manual ? Thank you.
Posted By: Alan Tam on Jun 10, 2015 07:41AMReply
You are right, there is no equation for placing a bracket on the slotted side of Housing Profile 2.
The distances for placing the bracket holes depend on your material thickness and if you keep the 2mm recommended remaining material to cover the slot. I can double check your design if you like, just email me your fpd files.
Posted By: Diane Haensel on Jun 11, 2015 12:00AMReply
Thanks, I will send in the fpd files later.
Posted By: Alan Tam on Jun 12, 2015 05:51AMReply
Should I send the files to firstname.lastname@example.org ?
Posted By: Alan Tam on Jun 12, 2015 12:24PM
yes, email@example.com works fine. Please mention the forum and have it to my attention.
Or you can send it to me directly at firstname.lastname@example.org
Posted By: Diane Haensel on Jun 12, 2015 10:23PMReply
How do I specify a hole with a larger circular cavity on top with the same circular centre ?
Do I simply insert a hole and then insert another circular cavity (with larger diameter) on the same centre ?
Posted By: Alan Tam on Jun 13, 2015 04:55PMReply
The electrical parts that I will put on top of the cover panel will weight 20 Kg.
The cover panel is 500mm x 360mm.
Can you recommend the thickness of the panel ? At this moment I use 4mm. Will that be enough ?
Posted By: Alan Tam on Jun 13, 2015 05:17PMReply
Yes, you can stack a cavity on top of a drilled hole or you can use "manual sinking parameter" and adjust sink depth and cone angle (180 degrees)
Posted By: Diane Haensel on Jun 16, 2015 01:04AMReply
20kg is quite some weight. Remember the top panel is only supported on the sides and some housing brackets on front and back. Does your design allow a block within the enclosure for additional support?
Posted By: Diane Haensel on Jun 16, 2015 01:13AMReply
Can you give a description or an example how I can specify a block to support weight on the panel ?
Posted By: Alan Tam on Jun 16, 2015 05:03AMReply
This is my second time to use the software and want to make a nice opening for RS 232 9 pin connector on the front panel. Is there easy way to do that?
Posted By: Carl on May 29, 2015 08:25PM Category: Front Panel Designer
You can find it in the macro objects.
--> view --> macro objects --> folder 'SubD-Connector' --> 9-pole...
You can ungroup the macro object and modify the holes if needed.
Posted By: Diane Haensel on Jun 01, 2015 06:23PMReply