Remove the feet. If accessible abolish the anxiety of the sofa (online furniture store - melodyhome) to affluence its access through doors. If this is not possible, skip to next step.
Move the sofa through the door. Slide the sofa on its back on the agenda (and furniture dollies) to the aboriginal door. If the anxiety are removed it should almost canyon appropriate through. If not, you may accept to bend it such that anniversary set of anxiety canyon through.
Move the sofa down the stairs. Abolish the furniture dollies, if you accept them. Slide the sofa advanced while captivation down burden on the ancillary extreme from the stairs. The sofa will activate to angle downwards as it is confused forward. Slowly acquiesce the sofa to lay on the stairs. Move the sofa until it is absolutely on the stairs. The being extreme down the stairs will charge to accomplish abiding the agenda does not bolt on the stairs and absolute the being accomplished on the stairs of if to push. The agenda reduces the abrasion amid the sofa and the stairs, appropriately authoritative the stairs an simple obstacle to accord with. If the stairs bend or change direction, as in a flight of stairs, you will charge to angle the sofa up on one of its ends (the arms). Again airing it, that is to say move it as admitting it were walking by sliding one ancillary again the other, to the next flight of stairs such that the agenda is adverse the ancillary of the stairs. Slowing lay the sofa down on the stairs. One being will charge to adviser the sofa down while ensuring that it does not blooper while the added being will charge to use their easily over their arch to affluence the sofa back down on the stairway slope. Repeat this footfall until the sofa is absolutely down the stairs.
Continue sliding the sofa. Slide the sofa, or alter the furniture dollies and roll, to its adapted location.
It is actual accessible to accept a brace of furniture dollies, if possible. They about alone amount $15.00 and are actual advantageous for added projects.
You can use straps with the winching adequacy to band the couch to the cardboard. This makes abiding that annihilation block loose.
You will charge at atomic two humans to accomplish this blazon of move. Otherwise you accident abrasion to yourself.
Back braces are also recommended to anticipate austere back injury.
Posted By: michelleloy on Oct 29, 2013 09:56AM Category: Whishes
All of a sudden with version 4.31 the origin when creating a new panel seems to be set willy-nilly. Never at a the bottom left corner as it used to be. Is it me or is there a reason for this?
Posted By: REPH11 on Oct 16, 2013 10:45PM Category: Front Panel Designer
No, there is no reason for it and I can't replicate it on my Windows installation. Do you run on Windows?
Until we have figured this out, quick fix is shortcut n + 1 (on number pad). This will bring the origing in the lower left corner. Imagine the number pad as your panel; upper left corner = 7, center = 5, lower right = 3, etc.
Posted By: DianeHaensel on Oct 16, 2013 11:48PMReply
I saw the same thing running Win 7 until I went into the Settings menu, set X origin and Y origin to zero (they already showed as zero but did it anyway) then ticked the "Use as default" box. Now it seems to be okay. All new designs put the origin in the lower left corner as desired.
Posted By: Vern_K on Oct 17, 2013 03:27AMReply
I did that myself and it worked. But it would only work if there was a panel defined. Perhaps the "default" settings could be changed before a panel needs to be defined.
Posted By: REPH11 on Oct 17, 2013 05:34PMReply
I need to create a rectangular cavity 40mm x 60mm that is 5mm deep in 10mm thick material. (That much is easy.) Now within that cavity, I would like to have another smaller rectangular cavity 20mm x 30mm that is an additional 3mm deep and also has edge machining (rounded edge 1.5mm radius) applied to it. This brings up some questions. How do I specify the smaller cavity depth in Front Panel Designer? Is it with respect to the top surface of the panel (in which case it should be 8mm) or is it with respect to the bottom of the larger cavity (in which case it should be 3mm)? Also, how do I know that the machining on the edge of the smaller cavity will be applied to the edge that is 5mm deep within the first cavity? In other words, how do I make sure the larger cavity is cut first, then the smaller one, then the edging on the smaller one? This same question applies to a similar situation with a through hole inside a cavity. Can I specify edge machining on a through hole sitting inside a cavity?
Posted By: Vern_K on Oct 16, 2013 04:37AM Category: Front Panel Designer
This is a good point.
The depth of a cavity is always related to the top surface. In your case, the second cavity has to be 8mm deep.
The edge on the second (lower) cavity can't be selected in FPD. We would mill air since the material is already removed by the larger cavity on top. However, we can make modifications in the milling program an lower the cutter. Please leave us a note in the production remarks and we will machine the edge of the lower cavity to your specifications.
Posted By: DianeHaensel on Oct 16, 2013 09:55PMReply
I am trying to import a .plt file but when I click import it doesn't show anything in preview or afterwards on my panel. Is there something I am doing wrong?
Posted By: aikenberry on Oct 08, 2013 05:12PM Category: Front Panel Designer
It's most likely a contour issue. Some doubled lines or unclosed contours can cause this.
Would you mind sending me your .plt file? I would like to have a look and fix this for you.
Posted By: DianeHaensel on Oct 10, 2013 12:41AMReply
Where should I send the file to?
Posted By: aikenberry on Oct 11, 2013 12:19AMReply
Please send it directly to me at email@example.com
Posted By: DianeHaensel on Oct 11, 2013 01:16AMReply
Is there a case where I can just remove the top only? I don't want to removed any side profiles of front panels or corner brackets.
Posted By: GoPDemon on Oct 04, 2013 04:42PM Category: Whishes
Maybe define the "Side Panel" as the top? and use the Housing Profile 2.
Posted By: RSnyder on Nov 13, 2013 07:07PMReply